ORIGINAL 

Router Table – Learn how to Use

admin

Wish to know tips on how to use a Router Table? Listed below are tricks to get essentially the most out of your router table.

You do not want a miter channel. Usually, you slide your work alongside the fence. If utilizing a miter channel, then the fence have to be sq. to the miter channel. Why go to that bother?

You may create a jig to glide alongside the Fence. This mechanically aligns the wooden to get a sq. lower. You can also make adjustment in profile and depth of lower. A Router Raise makes this straightforward.

A top quality Router Table fence eases dust assortment. Use your Router Table and Fence for simplicity and ease router bit set B09TR8Z82F TOOLDO!

It is best to by no means put your work between the fence and the router bit. That’s simply asking for bother.

Usually, you slide the wooden from proper to left (when wanting on the fence from the entrance). That’s an anti-climb lower. You make almost all cuts this manner.

If very cautious, you’ll be able to go a short distance in the other way. However you should maintain on tight to keep away from kickback and/or injury. This climb lower provides cleaner edges, however it is best to solely try it after loads of expertise.

Solely do lower than 15% of your work this manner. It is best to solely use shallow or light cuts. Do NOT take huge cuts. Solely do it while you palms are protected and away from the router bit.

Learn how to use a Router Table to middle edge-to-edge joints:

Have you ever ever puzzled tips on how to middle edge-to-edge joints? You utilize this method for making stable tabletops, huge panels, and even make edging to go round your router table high.

Let’s use an precise instance of oak edging on a MDF Router Table Prime. The highest is 1 1/8″ thick. The oak edging is 1 1/8″ thick.

How will we guarantee a centered edge?

  1. Determine on the tongue dimension. You may have a 1/4″ slot cutter. You need the tongue thickness lower than two occasions the lower. Due to this fact, the tongue thickness is barely lower than 1/2″. We use a 1/4″ depth of lower for this instance.
  2. We would like a tongue that’s lower than 1/2″ in thickness. Due to this fact, we all know that the rabbet on the Table Prime is barely greater than 5/16″ on each side of a 1 1/8″ thick piece.
  3. Rabbet the highest with a rabbet bit with a bearing to provide a 1/4″ rabbet. You do not wish to take lots throughout your first cross. Due to this fact, the depth of lower is ready for 1/8″ on your first cross.
  4. Set the fence so it’s even with the bearing of the rabbet bit.
  5. Lower each high and backside of the highest. Take your time and go all the best way round. Be sure that the workpiece is flat on the Router Table Prime. Or use the router on high of the workpiece.
  6. Measure the thickness of the tongue. Whether it is bigger than 1/2″, then regulate the depth of lower. A router raise makes this straightforward. Be aware: you rout each side; subsequently use one-half the adjustment for either side.
  7. Make your adjustment, rout the highest and backside once more. The tongue’s thickness is now barely lower than 1/2″.
  8. Change your rabbeting bit along with your 1/4″ slot cutter. I at all times disconnect the power supply to the router earlier than altering bits!
  9. Sit the rabbeted piece on the router tabletop close to the slot cutter. Elevate the Router so the underside of the slot cutter aligns with the underside of the tongue. Chances are you’ll want assist if the workpiece is massive.
  10. Set the depth of lower for the slot to round 3/16″ initially. Now slot your Oak edging. Flip it over and slot once more. Check the slot on the tongue. Is it too tight? In that case, do not forget that you make two passes with the slotter. Solely decrease your slot bit by 1/2 of the dimension wanted. By the best way, the Porter Cable 7518 Router makes this a snap.
  11. For the reason that slot lower is 1/4″, the second cross will not be utilizing all the cutter. You get an precisely middle slot that matches on the tongue.
  12. As soon as the slot (groove) matches on the tongue, you might be able to set your ultimate depth of the groove. The ultimate depth of lower is barely greater than 1/4″ to permit for glue.
  13. Set your fence for this ultimate depth. Keep in mind – make two passes with the slotter. This provides you a precise match.

 

You should use this technique for any edge-to-edge joinery, resembling tabletops, panels, massive drawer fronts, and any time you wish to be part of two-pieces. You get good alignment and a rock-solid joint.

If you wish to see how this takes care of glue-up, please go to Router Table Prime

To make your personal router raise, go to a simple to make Router Raise

For extra data on Utilizing Your Router Table, together with photos and suggestions, please go to Learn how to Use a Router Table